How To Clean A Glock 17 Gen 4 9mm

Download Article

If you lot ain a Glock pistol, it is of import that you know how to detach information technology to perform general maintenance. While there are many different types of Glock pistols, you tin disassemble them all in much the same way. Follow this guide to safely field strip your Glock in just a few minutes.

1
Point the pistol in a safety direction. Make certain that the pistol is pointed in a direction where any accidental discharge cannot cause physical harm to you or anyone else.^[1]
- Keep your finger away from the trigger, and exterior of the guard. This will help prevent accidental firing.^[2]
2

Release the magazine. Press the magazine release with your pollex and remove the mag with your other paw.

Advert
3

Open up the slide. While continuing to point the gun in a safe direction, pull the slide back and lock it open with the slide stop lever. Y'all can push button the lever upwards with your thumb while holding the slide back with your other manus. This will hold the slide open.
4
Check for remaining armament. Once the slide is open, look into the sleeping room and ensure that no ammunition remains in the gun. Use your pinky finger to sweep for ammunition in the chamber as well.^[three]
- Check three times for remaining ammunition before proceeding to detach the gun.
Ad

1

Put on safety glasses. There are several components that are jump-loaded and tin cause serious center damage. The glasses will likewise assist protect from solvents and lubricants getting in your eyes.
2

Close the slide. Pull the slide back to release the stop lever. The slide will shut. Point the gun in a safe direction and pull the trigger to release the firing pivot.^[iv]
3

Grip the gun. Agree the gun in one mitt, with four fingers around the acme of the slide, and the thumb property the grip.
4

Pull back the slide. Using the 4 fingers on the top of the slide, pull information technology back near 1/10th of an inch. If you pull information technology dorsum as well far, you will need to pull the slide all the style back and restart the process.
5

Pull downwardly the slide lock. Using your other hand, pull downwards both sides of the slide lock lever. Push the slide frontwards with your four fingers until it has separated from the receiver of the gun.

Advertisement

one

Remove the spring. Push button the leap forward slightly and lift it away from the barrel. The leap is under force per unit area, then exist careful when removing information technology.
ii

Pull the barrel out of the slide. Hold the butt by the extruding lugs. Elevator the butt while pushing forwards slightly. Raise and pull the barrel out of the slide.^[5]
3

Clean the gun. One time the Glock has been disassembled, y'all can continue to clean the gun. Yous do not need to disassemble the Glock any further than this to properly make clean and maintain it.^[vi]
4

Reassemble the gun. Once you are finished cleaning, you can reassemble the gun past reversing the above steps. You volition non need to concord the slide lock down when putting the slide back on the receiver.

Advertisement

Add together New Question

Question

What to do if wire comes completely out of braces before seeing a dentist?

Jax Monroe

Community Answer

Practice zilch. Just wait. Endeavor to get the dentist to schedule a coming together sooner than they offered by explaining what has happened.

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizement

It is recommended that you wear safe glasses, since there are bound loaded parts that could cause heart harm.

Thank you for submitting a tip for review!

Make sure the pistol is always pointing abroad from yourself and anyone else.
Never look down the front of the gun barrel to check if sleeping room is unloaded.
NEVER, during the disassembly, should your finger be on the trigger.

About This Article

Commodity Summary X

To disassemble a Glock pistol, y'all'll need to safely unload it then remove the slide and butt. First, you'll demand to point the gun in a safe management and release the mag. Pull open and lock the slide and then you can check the chamber for whatsoever remaining armament. Adjacent, y'all should close the slide and burn down once in a safe management to release the firing pin. Afterwards, open up the slide slightly and pull downwards on both sides of the slide lock. In one case the lock is in identify, you lot can push button the slide forward to separate it from the gun. You'll also demand to push button the jump forwards out of the gun and pull out the barrel. When these parts of the gun are removed, you tin can clean your Glock before reassembling it. Remember to habiliment prophylactic goggles when working with your gun in case of any accidents. For tips on how to put the slide back on when reassembling your gun, go along reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 156,283 times.